Awesome quality manual. You really saved my bacon with this one. Was looking for some specific information with regards to my "new" vintage VCR that didn't come with the owners manual. This site is truely a goldmine of available manuals. The quality of the scans are top notch.
Thank-you so much for this awesome manual. If you're looking for this Sony SL-HF400 owners manual, this is the one you NEED to buy. Definitely worth the money.
The manual was made available promptly. I is a clean scan of the original. I had no problem downloading it. The scan was well centered and cleanly formatted. It is as good a product as can be had without being the original document.
Received downlink in less then 8 hours, Item was in good copy condition, and told me how to program the clock timer. The price was very resonable, and the process was very automated and was GREAT to work with.
I was very pleased with the manual I got for my amateur (ham) radio. Without it I could not figure out how to input and/or change the P/L setting on my radio. It drove me nuts as the radio was essentially useless. That all changed when my manual came. Then it took only minutes and I was done. Now my radio works fine. This is an exceptionally good resource as it's a very easy and user friendly download. Thank you very much! DziÄkujemy za!
Text excerpt from page 13 (click to view)
Assembling the spray guard and trimmer head Superauto II (322L, 325L-X/L-XT)
â¢ Fit the guard (A) intended for use with the trimmer head. Hook the guard onto the shaft fitting and secure it with the bolt (L). â¢ Fit the drive disc (B) on the output axle. â¢ Turn the blade axle until one of the holes in the drive disc aligns with the hole in the gear housing. â¢ Insert the locking pin (C) in the hole so that the axle is locked. â¢ The trimmer head must be split to be fitted (see the diagram). Proceed as follows: â¢ Insert your finger into the centre hole of the cover (I) at the same time as you hold the cover with your other fingers. Press the two catches (J) that extend from the cut-out on the bottom section (K) using the thumb and index finger of your other hand. Press apart the trimmer head using the fingers on the cover. â¢ Place the cover (I) and the support flange (F) on the output axle. â¢ Fit the nut (G). The tightening torque of the nut is 35-50 Nm (3,5-5 kpm). Use the socket spanner in the tool kit. Hold the handle of the spanner as close to the trimmer guard as possible. The nut is tightened when the spanner is turned against the direction of rotation (left-hand thread). â¢ Fit the trimmer headâs bottom section (K) on the cover (I) by pressing the two sections together with the cut-outs on the bottom section aligned with the catches on the cover. â¢ To dismantle follow the instructions in the reverse order.
A J K I
Assembling other guards and cutting equipment (322L, 325L-X/L-XT)
â¢ Fit the guard (A) intended for use with the trimmer head. Hook the guard onto the shaft fitting and secure it with the bolt (L).
â¢ Fit the disc drive (B) on the output axle.
â¢ Turn the blade axle until one of the disc driveâs holes aligns with the corresponding hole in the gear housing.
â¢ Insert the locking pin (C) into the hole to lock the axle.
â¢ Screw on the trimmer head (H) in the direction of rotation.
G F I
â¢ Dismantling takes place in the reverse order.
Fitting the spray guard and trimmer head (322C)
Guard â¢ Fit the guard as shown in the diagram. Tighten securely. Trimmer head â¢ Fit the dust cup on the shaft. The nut must be completely covered by the dust cup. â¢ Hold the dust cup with a spanner to prevent the shaft from rotating. â¢ Screw the trimmer head onto the shaft.