There are currently no product reviews.
Excellent service from this company (including a total refund on an earlier purchase when through no fault of the company the manual was incomplete). I have purchased several manuals which I have been very satisfied with, as I am with this one. Highly recommended.
It was easy to order and received exactly what I needed. Only complaint would be the 24 hours you have to wait.
Manual was delivered in a timely manner and was all in English as advertised. The manuals I received when we moved into our flat were in German, Italian, and French. Having never used a steamer before, and not speaking/reading German very well, I needed an English Manual. this was a huge help.
Great Manual. This manual is available no where else. It was exactly what I was looking for. Only in German.
This GRUNDIG UV5A Owner Manual is not only an instruction manual but a total functional circuit description of the Multimeter and includes circuit diagram at the end pages. It is very helpful for repairing and calibrating the instrument. It is written in two languages English and German for international support. It was very easy to repair my unit with this document. Regards, Regis Pauly, Electrical Engineer.
IMPORTANT! The power cutter is equipped with a two-stroke engine and must always been run using a mixture of petrol and two-stroke engine oil. It is important to accurately measure the amount of oil to be mixed to ensure that the correct mixture is obtained. When mixing small amounts of fuel, even small inaccuracies can drastically affect the ratio of the mixture.
WARNING!The following precautions reduce the risk of fire:
Always provide for good ventilation when handling fuel.
â¢ Do not smoke or place any sources of heat in the vicinity of the fuel. â¢ Never refuel when the engine is running. â¢ Open the fuel cap slowly when fuelling so that any over pressure is released slowly. â¢ Tighten the fuel cap carefully after refuelling. â¢ Always move the machine from the fuelling place before starting. â¢ Keep the handle dry, clean and free from oil and fuel.
â¢ Use good quality unleaded or leaded petrol. â¢ The lowest octane recommended is 90. â¢ If you run the engine on a lower octane grade than 90 so-called, knocking can occur. This gives rise to a high engine temperature, which can result in serious engine damage.
â¢ For the best results use HUSQVARNA two-stroke oil, which is especially developed for power cutters. Mixing ratio 1:50 (2%). â¢ If HUSQVARNA two-stroke oil is not available, you may use another two-stroke oil of good quality that is intended for air cooled engines. Contact your dealer when selecting an oil. Mixing ratio 1:33 (3%)-1:25 (4%). â¢ Never use two-stroke oil intended for water cooled outboard engines, so-called, outboard oil. â¢ Never use oil intended for four-stroke engines.
Gasolin Benzin Essence Gasolina Lit.
Oil â¢ Ãl Huile â¢ Aceite Lit.
â¢ Clean around the fuel cap. Clean the fuel tank regularly. The fuel filter should be changed at least once per year Contamination in the tank can disrupt operations. Ensure that the fuel is well mixed by shaking the container before filling the tank.
5 10 15 20
2%(1:50) 3%(1:33) 4%(1:25) 0,10 0,15 0,20 0,20 0,30 0,40 0,30 0,40 0,45 0,60
US fl. oz.
1 2 1/2 5
2%(1:50) 3%(1:33) 4%(1:25) 2 1/2 3 3/4 5 1/8 6 1/2 9 3/4 12 7/8 12 7/8 19 1/4 25 3/4
â¢ Always exercise care when filling the fuel. Move the power cutter at least three metres from the filling area before starting. Make sure the fuel cap is tightened.
â¢ Always mix the petrol and oil in a clean container intended for fuel. â¢ Always start by filling half the amount of the petrol to be used. Then add the entire amount of oil. Mix (shake) the fuel mixture. Add the remaining amount of petrol. â¢ Mix (shake) the fuel mixture thoroughly before filling the sawâs fuel tank. â¢ Do not mix more than max. one monthâs supply of fuel. â¢ If the power cutter is not used for some time the fuel tank should be emptied and cleaned.
Min 3 m (10ft)
14 â English