|
|
|
Who's Online
There currently are 6043 guests online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Manual was destroyed and this purchase made it possible to recover my manual . It was easy to down load and smooth to use thanks .
 ;
Turns out this was not the manual i was looking for. The concertmate 670 keyboard i have is a "Realistic" model made for Radio Shack and none of the diagrams on the owners manual i received matches up. HOWEVER, I must say the service Owners Manual provides was fast and efficient by being available online. The manual was in good readable condition and easily downloaded.
;
Great price, Quick delivery, the document was very usefull A+++++++++++++++
;
Thank´s for your help, I already recived these manual from you
;
Thank you for your manual It has the basic things to and i use the Oszi for Longer Time.
THX
SERVICE AND ADJUSTMENTS
R.H. SUSPENSION ARM MANDREL PULLEY ENGINE PULLEY
TO REPLACE MOTION DRIVE BELT (See Fig. 22)
Park the tractor on level surface. Engage parking brake. For assistance, there is a belt installation guide decal on bottom side of left footrest. BELT REMOVAL � Remove mower (See �TO REMOVE MOWER� in this section of manual). NOTE: Observe entire motion drive belt and position of all belt guides and keepers. � � � Remove belt from stationary idler and clutching idler. Remove belt downward from around engine pulley. Pull belt slack toward rear of tractor. Remove belt upwards from transaxle pulley by de�ecting belt keepers. Remove belt from center span keeper and pull belt away from tractor.
3 8
2
RETAINER SPRING
IDLER PULLEYS
MANDREL PULLEY
4
FIG. 20
�
TO CHECK AND ADJUST BRAKE (See Fig. 21)
Your tractor is equipped with an adjustable brake system which is mounted on the right side of the transaxle. If tractor requires more than �ve (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be checked and adjusted. TO CHECK BRAKE � Park tractor on a level, dry concrete or paved surface, depress clutch/brake pedal all the way down and engage parking brake. � Place gear shift lever in neutral (N) position. The rear wheels must lock and skid when you try to manually push the tractor forward. If the rear wheels rotate, the brake needs to be adjusted or the pads need to be replaced. TO ADJUST BRAKE � Depress clutch/brake pedal all the way down and engage parking brake. � Measure distance between brake operating arm and nut �A� on brake rod. � If distance is other than 1-1/2", loosen jam nut and turn nut �A� until distance becomes 1-1/2". Retighten jam nut against nut �A�. � Road test tractor for proper stopping distance as stated above. Readjust if necessary. If stopping distance is still greater than �ve (5) feet in highest gear, further maintenance is necessary. Replace brake pads or contact a quali�ed service center.
WITH PARKING BRAKE �ENGAGED�
1-1/2"
BELT INSTALLATION � Carefully work new belt down between transaxle belt keepers and onto the input pulley. � Slide belt into the center span keeper. � Pull belt toward front of tractor and roll around the top groove of engine pulley. � Install belt through stationary idler and clutching idler. � Make sure belt is in all pulley grooves and inside all belt guides and keepers. � Install mower (See �TO INSTALL MOWER� in this section of manual).
ENGINE PULLEY
CLUTCHING IDLER
STATIONARY IDLER
CENTER SPAN KEEPER
TRANSAXLE PULLEY
FIG. 22
NUT �A� JAM NUT
TRANSAXLE GEAR SHIFT LEVER NEUTRALADJUSTMENT (See Fig. 23)
The transaxle should be in neutral when the gear shift lever is in neutral (N) (lock gate) position. The adjustment is preset at the factory; however, if adjustment is needed, proceed as follows: � Make sure transaxle is in neutral (N). NOTE: When the tractor rear wheels move freely, the transaxle is in neutral. � Loosen adjustment bolt in front of the right rear
OPERATING ARM
00238
FIG. 21
21
wheel.
|
|
|
> |
|
