|
|
|
Who's Online
There currently are 5905 guests online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Thank´s for your help, I already recived these manual from you
;
Thank you for your manual It has the basic things to and i use the Oszi for Longer Time.
THX
;
Actually, I was looking for this information for 3 years!...now thanks to you, the manual is on my hands and of great help, cause I understand now where I was doing wrong connections and wires...excellent, I'll be back to you if in need, thank you.
 ;
This manual covers the main equipment features only. While it also includes the procedure for saving and loading from the now long obsolete memory cards it does not mention the how to operate with the optional floppy drive interface so I am still at a loss about how to use this! Note that there is a separate manual covering the MIDI interface and programming via the keyboard, not included in this download. You will also need to get hold of this if you want to use the MIDI interface properly. Basically there is little difference between this manual and the free to download manual for the similar PR60 model.
;
Good list of manuals. I found a very rare one and easily get. Should be promptly to download, as we must to wait hours even after confirmed payment.
OPERATION
The cutting height range is approximately 1-1/2" to 4". The heights are measured from the ground to the blade tip with the engine not running. These heights are approximate and may vary depending upon soil conditions, height of grass and types of grass being mowed. � The average lawn should be cut to approximately 2-1/2 inches during the cool season and to over 3 inches during hot months. For healthier and better looking lawns, mow often and after moderate growth. � For best cutting performance, grass over 6 inches in height should be mowed twice. Make the �rst cut relatively high; the second to desired height. � TO STOP MOWER BLADES - disengage attachment clutch control. CAUTION: Do not operate the mower without either the entire grass catcher, on mowers so equipped, or the de�ector shield in place.
PULL OUT TO "ENGAGE" ATTACHMENT LIFT LEVER HIGH POSITION
TO ADJUST GAUGE WHEELS (See Fig. 9)
Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in proper position to help prevent scalping in most terrain conditions. NOTE:Adjust gauge wheels with tractor on a �at level surface. � Adjust mower to desired cutting height (See �TO ADJUST MOWER CUTTING HEIGHT� in the Operation section of this manual). Remove retainer spring and clevis pin which secure each gauge wheel bar. Lower gauge wheels to ground. Raise gauge wheels slightly to align holes in bracket and gauge wheel bar and insert clevis pin. Gauge wheels should be slightly off the ground. Replace retainer spring into clevis pin. Be sure all gauge wheels are in the same setting.
LOW POSITION
ATTACHMENT CLUTCH SWITCH PUSH IN TO "DISENGAGED"
� �
021
42
DEFLECTOR SHIELD
� �
FIG. 10
IMPORTANT: BE SURE TO READJUST GAUGE WHEELS IFYOU CHANGE THE CUTTING HEIGHT OF THE MOWER DECK.
TO OPERATE ON HILLS
WARNING: Do not drive up or down hills with slopes greater than 15° and do not drive across any slope.
RETAINER SPRING
019 77
� � � �
CLEVIS PIN
� �
Choose the slowest speed before starting up or down hills. Avoid stopping or changing speed on hills. If stopping is absolutely necessary, push brake pedal quickly to brake position and engage parking brake. To restart movement, slowly release parking brake and brake pedal. Slowly depress appropriate drive pedal to slowest setting. Make all turns slowly.
FIG. 9
TO TRANSPORT (See Figs. 7 and 11)
When pushing or towing your tractor, be sure to disengage transmission by placing freewheel control in freewheeling position. Free wheel control is located at the rear drawbar of tractor. � Raise attachment lift to highest position with attachment lift control. � Pull freewheel control out and into the slot and release so it is held in the disengaged position. � Do not push or tow tractor at more than two (2) MPH. � To reengage transmission, reverse above procedure.
TO OPERATE MOWER (See Fig. 10)
Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine. You must remain fully and centrally positioned in the seat to prevent the engine from hesitating or cutting off when operating your equipment on rough, rolling terrain or hills. � Select desired height of cut. � Lower mower with attachment lift control. � Start mower blades by engaging attachment clutch control.
13
|
|
|
> |
|
